Here's 3oneAirsoft MF-AB2.....and updated version of the mf-ab.
Features:
1. Full active braking that is gentle enough not to harm the motor but still stops the motor very quickly.
2. Fully assembled, production tested.
3. Built in heatsink.
4. The MOSFETs are fully protected against voltage spikes from the motor.
5. It is almost impossible to cross conduct the MOSFETs.
6. Fully protected against static discharge.
7. Resistant to water and condensation.
8. The circuit draws no current when not triggered.
9. The trigger circuit needs considerable current to turn on preventing false firing from condensation, grease, etc.
10. Uses surface mount parts to minimize size.
11. Very tolerant of bad wiring, bad layout, noise, etc.
12. Failure of the active breaking MOSFET can't turn the gun uncontrollably on.
13. 2nd Generation formfactor used is much compact
14. screw-in connectors for easy mounting
15. Thermal Circuitbreaker protection
The Actual Manual
Here's what inside the whole package...
There's a tamiya plug, shrink tubes and angled terminal connectors though I hope Komrad 3One
would just put 2 pairs of straight terminal connectors in the future much better imo
if the owner wana use them as plugs for battery to mosfet.
The Specs...
The MF-AB2 mosfet switch...
It's smaller to the fuse box and even smaller to the
Toyota Horn Relay I've been using for all this years.
Really good hi-temp wires...gauges 16-24.
Installation was really easy compared to installing a relay on my beat-up
stock JG version 3 gb from my JG Dragunov hehe.
The wires are now screwed-in compared to mf-ab1 which are pre-soldered
on the circuit board. This is much better for people who prefer using other types of wires
like those highly expensive silicone wires. Also good for swapping mosfet if the user wanna
upgrade to more advance mosfet system made by Komrad 3One.
I prefer using terminal connectors than tamiya type plugs since they connect way sturdier and tight
so resistance is way lower aside way way cheaper compared to Dean's plugs.
Demo on the active breaking feature...
http://www.youtube.com/watch?v=kBNLmnL3ZLw[/URL]
- Notice how the nozzle stays in full forward position by using the feathering technique to FULLY decock/decompress
the aeg. Sometimes nozzle slightly goes back due to the huge sector cheap I installed as shown
on my JG Dragunov review at FilAKairsoft.com.
- Also shown though for AK's only is another way to check if spring is fully decocked is
by wiggling the sector gear tooth as show on the last part of vid if the cover on the sector has been remove that is.
If spring ain't fully decock the sector gear is very stiff.
- Notice also the ghost of George Harrison on the reciever hehehehe.
Interested party to this cool mosfet plz pm Komrad 3One at FAS or txt him..09276476597.
Available soon at Brojames as well.
Features:
1. Full active braking that is gentle enough not to harm the motor but still stops the motor very quickly.
2. Fully assembled, production tested.
3. Built in heatsink.
4. The MOSFETs are fully protected against voltage spikes from the motor.
5. It is almost impossible to cross conduct the MOSFETs.
6. Fully protected against static discharge.
7. Resistant to water and condensation.
8. The circuit draws no current when not triggered.
9. The trigger circuit needs considerable current to turn on preventing false firing from condensation, grease, etc.
10. Uses surface mount parts to minimize size.
11. Very tolerant of bad wiring, bad layout, noise, etc.
12. Failure of the active breaking MOSFET can't turn the gun uncontrollably on.
13. 2nd Generation formfactor used is much compact
14. screw-in connectors for easy mounting
15. Thermal Circuitbreaker protection
The Actual Manual
Here's what inside the whole package...
There's a tamiya plug, shrink tubes and angled terminal connectors though I hope Komrad 3One
would just put 2 pairs of straight terminal connectors in the future much better imo
if the owner wana use them as plugs for battery to mosfet.
The Specs...
The MF-AB2 mosfet switch...
It's smaller to the fuse box and even smaller to the
Toyota Horn Relay I've been using for all this years.
Really good hi-temp wires...gauges 16-24.
Installation was really easy compared to installing a relay on my beat-up
stock JG version 3 gb from my JG Dragunov hehe.
The wires are now screwed-in compared to mf-ab1 which are pre-soldered
on the circuit board. This is much better for people who prefer using other types of wires
like those highly expensive silicone wires. Also good for swapping mosfet if the user wanna
upgrade to more advance mosfet system made by Komrad 3One.
I prefer using terminal connectors than tamiya type plugs since they connect way sturdier and tight
so resistance is way lower aside way way cheaper compared to Dean's plugs.
Demo on the active breaking feature...
http://www.youtube.com/watch?v=kBNLmnL3ZLw[/URL]
- Notice how the nozzle stays in full forward position by using the feathering technique to FULLY decock/decompress
the aeg. Sometimes nozzle slightly goes back due to the huge sector cheap I installed as shown
on my JG Dragunov review at FilAKairsoft.com.
- Also shown though for AK's only is another way to check if spring is fully decocked is
by wiggling the sector gear tooth as show on the last part of vid if the cover on the sector has been remove that is.
If spring ain't fully decock the sector gear is very stiff.
- Notice also the ghost of George Harrison on the reciever hehehehe.
Interested party to this cool mosfet plz pm Komrad 3One at FAS or txt him..09276476597.
Available soon at Brojames as well.
![filakairsoft/clap.gif](http://filakairsoft.30.<a href="http://www.forumer.com">forumer</a>.com/html/emoticons/filakairsoft/clap.gif)