Hi all
What i am ware that a lot of you players out there use Lipo battires
As a noob when it comes to this i need help an advise and this is also for the newer player that want to go the route.

I have read a fair amount about the subject what i would like is the advice from you guy who have gone tru the pains and hassled.

Here is what i own aeg wize and what i am looking at .
Kalash RK01 x2
RK02
CM040d
CM048m next week.
I would like to run them still stock for now , and have been told the a 7.2v Lipo is very similar to a 9.6v.
But I can not seem to fined 7.2v but only 11.1v batters

Here are some of the parts i am looking at

Supplier RSOV

A.C.M. Li-Polymer battery cells voltage monitor and alarm buzzer

A.C.M. Li-Polymer battery cells voltage indicator( do i need this?)

Firefox' 11.1v 1200mah (20C) Li-Polymer stick battery pack fits AK47/74 and MP5K AEG Size : 168 x 13 x 13mm (not include electrical wire)
or
Firefox' 11.1v 1350mah (12C) Li-Polymer stick battery pack, length: 19.8cm.

Firefox' intelligent Li-ion Polymer balancer charger set for 7.4v & 11.1v, come with a 110v-240v charger.
Or
'Esky' balancer charger set for Li-ion Polymer battery pack(7.4V & 11.1V)

Please could you give more info or suggsetions

Thank you

I could not wait so i ordered off ehoddyasia they seem to have the 7.4v 1600 and a nice G&P charger cost was 46 usd . I will be testing it against my 9.6v 1500($64 )sanyo nic cab and see how it performs.

Any advice?

Sorry for the late reply.

• If you can't find a 7.4v lipo, just modify it and you can always reconnect the other cell when times come you needed a higher voltage.
  I saw a 7.4v lipo at airsoftglobal
  Link form AG: here and here, check the dimension first.
  You can contact them,
  Other lipo batt from WGC(and IMAX chargers).
• DON'T EVER USE THE ESKY CHARGER, try other brand (IMAX B6 or B8 or other brand with good review).
  Saw this also from RSOV but don't know yet specs and review.
  Also this one.
• Try another lipo brand instead a firefox.
• Li-Polymer battery cells voltage monitor and alarm buzzer is good for field testing. You don't have to buy the other lipo indicator. Lipo indicator also good for the exact battery voltage.
• Other alternative source of battery and charger, try the RC forums.

oh...didn't see this, you already ordered.
Seems a good choice.
Just remember, do not over drain the batt.
Charge immediately after using it.

I want to get
A.C.M. Li-Polymer battery cells voltage monitor and alarm buzzer but i cannot seem to find another supplier than rosv that sell the item but the item is very cheap but the shipping is $25.00 a bit steep

gavin

You can always use your MultiTester to check the Lipo Batt komrad.
Check point is the balancer connector.
Lipo Batt fully charged should be 4.2 volts per cell.
Your balancer automatically shut at that level.
Do not use the battery below 3.0 volts each cell, or to be safe limit it to 3.5volts then charge the batt immidietely.
Important is not to exceed both the high voltage of 4.2 volts each cell and the low voltage of 3.0 volts each cell.
Exceeding these limits can harm/damage the battery.

thanks for the help I will speak to a friend in the team he is a elector bof
and a fellow AK user