Gud day mga komrad,

Just a querry about the JG dragunov plastic reciever, pwede ko po ba palitan yun ng JG metal reciever ng AK47? Compatible po ba yun or if not, ano po ang compatible na replacement para sa JG plastic reciever.

Rgds,
Ironcross_21

compatible komrad

komrad do I need some modification if I'm going to use a metal JG AK47 re; pag sinalpak ko na po yun gbox assy at yun front assy including the butt. compatible po ba lahat? madami pong salamat ulit.

I am talking with gearbox and front end compatibilty

Too bad, kilangan mo dito ay ang JG AK47S receiver unless Mod mo ang rear part ng JG AK47 receiver para maipasok mo ang butt.

thanks for the info again komrad, if no available JG ak47s I'll just buy the jg ak47 na lang cguro and minor trimming na lang sa rear end ng rcvr. Salamat po sa mga guro...mabuhay ang AK lovers

master kano po ba dragunov ngaun? anu po ba maganda setup ng dragunov pang DM?

maraming salamat po master's!!!!




PS;
juz manage to own the cm048m can i apply to be a Komrad?

yung full metal na JG draugunov nasa aroud 6500 ata.
pero yung plastic version gaya ng sa kin eh mga 5k ata.

lately medyo nagmahal mga baril dahil sa dami ng komplikasyon daw
so konting tulong na lang natin sa mga nagbebenta ng baril kung medyo mahal benta nila lately lalu na sa mga nasa pwesto tlga.

set-up sa dm......maganda naka sp150.....or sp170 hehe....like this......

Heto set-up ng sa kin....nung time na gusto ko lang tlga matikman yung malakas at mahabang beng tlga...using a JG Dragunov.

-sp170
-9.6 volts 3200 nimh subc external batts
-TM eg1000
-CA v3 mgb
-SRC stainless steel tight barrel 650 mm/6.03 id
-deepfire piston body with titanium half-tooth
-techpro spring guide with bearing
-CA bore up kit except a T6 aluminum piston head machine made by MR.S
-guarder ITU
-src ak47 metal hop assembly
-relay .....(without this sunog agad switch assembly ko sa kaka semi)
-modified hard type hop up rubber of Prometheus

FPS.......550 @ .3...fully settled.

komrad rambo, naka CA bore up din ako. and masasabi ko na indi ganun kaganda ang piston head nya. is there any chance na makakuha ako ng aluminum piston head na kagaya ng inyo? gusto ko sana pagawa din eh. kung ok sa inyo pa PM na lang sakin. salamat!

komrads,

ok ba ang jg svd gawing squad support weapon? using an electric drum magazine? kaya ng stock ang continous bursts? never mind kung mga 350 FPS lang basta maganda ROF nya?

anyone tried it for this purpose? on all stock?

hehe did that komrad when i downgraded this very long aeg.
i was using a 12 volts sub-c nicads externally of course.
but mine was firing at 490 fps with an rof of roughly around 20 rps
tnx to that 12 volts battery hehe.

the whole set-up of that i think has been posted on older pages of this thread.

one of problem with this is you really need a 650mm barrel cause sometimes the bb's hit the external barrel before it goes out resulting in very erratic flight if you just use the stock barrel which is only an ak length.
don't know about the metal version if JG installed a longer barrel atleast an m16 length.

okay. thanks!

kasi I was thinking of this idea kasi hirap maghanap ng RPK and kung meron man, mahal naman sya.

that's one of the reason this is still a very practical/multi platform for those who wanna go sniping or be the machine gunner/ rambo mode every now and then hehe.

also it's light enough it's basically the lightest ak i have once i slap on a drum mag it's still fairly light...i can almost say....who needs a heavy bulky m249 or m60 hehe.

I might work on it again to concentrate on the looks. some external modding to make it more like an elongated customized ak than a wannabee svd hehe.

komrads ok po ba kung convert ko na lang cm048m ko to dragunov or bibili ako dragunov mismo?

saka as far po dito sa bnigay mo set up sa akin anu po dapat ko tanggalin dito for high fps setup

-sp170
-9.6 volts 3200 nimh subc external batts
-TM eg1000
-CA v3 mgb
-SRC stainless steel tight barrel 650 mm/6.03 id
-deepfire piston body with titanium half-tooth
-techpro spring guide with bearing
-CA bore up kit except a T6 aluminum piston head machine made by MR.S
-guarder ITU
-src ak47 metal hop assembly
-relay .....(without this sunog agad switch assembly ko sa kaka semi)
-modified hard type hop up rubber of Prometheus

FPS.......550 @ .3...fully settled.


maraming salamt po komrad!

better go for a cyma-048m for better much cleaner look.
mahaba masyado jg dragunov baka mahirapan ka lang sa pag handle dyan.
pero kung sanay ka sa mahaba then go for it...yun nga lang madami ka pa ggastusin kumpara sa cm-048m.

sa set-up....well to make it simple for you stick to those internal parts concerning the gb para makatipid hehe.

komrad question lng po, hindi ba mdling mtangal ung butt stock nitong JG Dragunov? Ano po kayang magandang solution dun? Balak ko kasi bumili next week, pinagpipilian ko kng ito o yung bolt action. Full-auto!!!hehe

Pasensya po, newbie lang po.
Thanks in advance. peace.